Current Issue
August 2010
• Electro-Mechanical Broadband RF Switch.
• Single-Stage Driver Amplifier
• Quad-Band EDGE Radio Solution
• Modeling 3G / WCDMA / HSDPA
• Composite Filters
• Integration of Waveguide
• Coaxial Components
• Antennas Needed
• And More...
 
Dow-Key Microwave
 
  Search by TXTLINX Number:
 
   

Fully Matched Cascadable Amp
The TQP3M9009 has been added to the company’s low noise gain block family for high performance 3G/4G infrastructure. This cascadable amplifier is fully matched internally, allowing designers to focus on system level needs. It operates over a broad .05 to 4 GHz frequency range.

Bandpass Filter
Part number 2965-SMA is a 500 MHz bandpass filter. The filter has a typical 1 dB bandwidth of 8 MHz, insertion loss of 6.5 dB and typical 40 dB bandwidth of 52 MHz. It is supplied in a 0.6 x 0.6 x 2.25" SMA package and may be customized for other center frequencies and bandwidths.

UltraFast™ Digitally Programmable LDO
The LT3071 is the second in a family of digitally programmable linear regulators with the lowest dropout voltage, lowest noise, and fastest transient response of any monolithic 5A LDO currently available. Dropout voltage at 5A is an ultralow 85mV. Its QFN package is 4 x 5 x 0.75mm in size.


Microwave Power MMIC
A 4W C-Band GaAs MMIC for satellite applications, the TMD0608-4 operates in the 5.65 to 8.50 GHz range. With this broad bandwidth, a high gain of 27 dB throughout the operating range, and 50 ohm internal matching, this device is well suited for use as a pre-amplifier in C-Band satellite and terrestrial communications.

USB Power Sensors
The U2000 Series USB-based power sensors are compact, portable solutions that allow average power measurements without power meters. All sensors, except the U2004A model, feature internal triggering and trace display capabilities. Current users of these sensors can upgrade their firmware for free.

Directional Couplers
Miniature air dielectric directional couplers are rugged, lightweight devices that offer lower insertion loss than comparable stripline units. The simplified construction allows for greater flexibility in creating customized configurations. Any port can be used as the input with these devices.

Elliptic Lowpass Filter
Part number 2969-SMA is a high order 10 MHz elliptic lowpass filter with sharp transition to the stopband and high stopband attenuation. Typical 1 dB bandwidth is 10.9 MHz with minimum 84 dB attenuation at 13.125 MHz. It is supplied in a 0.6 x 0.6 2.25" package with SMA connectors.

Directional Coupler
Model 110067016 directional coupler has a frequency range of 10 to 67 GHz, 7.25 directivity, and maximum VSWR (any port) of 2.0. Coupling (with respect to output) is 16 +/-1.1 dB and frequency sensitivity is +/-2.0 dB. Operating temperature range is -54 to +85ºC.

Fixed Frequency Synthesizer
The SFS6400A-LF in C-band is a single frequency synthesizer that operates at 6400 MHz. This synthesizer features a typical phase noise of -88 dBc/Hz @ 10 KHz offset and typical sideband spurs of -65 dBc. Its PLL-V12N package measures only 0.60 x 0.60 x 0.13".

Higher Power GaAs FETs
The company has expanded its Ku-Band GaAs FET lineup with two higher output power devices rated for 18 and 30W. Models TIM1213-18L and TIM1213-30L operate in the 12.7 to 13.2 GHz range and are targeted for use in microwave radios for microwave links and satellite communications.
 
EMT SMT Diode TVS Connectors
Now available are transient protection solutions embedded within the connector shell utilizing surface mount (SMT) diodes. Using SMT diode technology allows for increased flexibility in the packaging of transient protection within the connector, saving both space and weight.


Low Noise Gain Block
Model TQP3M9008 is a new low noise gain block that offers high gain over a broad .05 to 4 GHz frequency range. It is a cascadable amplifier that requires no external matching components and can reduce BOMs. The gain block provides 35.5 dBm OIP3, while maintaining a low 1.3 dB noise figure.

 

 

 

January 2008

1 | 2 | 3 | 4 | 5 | 6 | 7 

Uni-Matic Preform Loader

The Uni-Matic epoxy preform loader provides an inexpensive, cost-effective method for loading high volumes of epoxy preforms. Depending upon component and preform geometry, the Uni-Matic feeds at rates of 200 to 600 preforms per minute.
Multi-Seals
Click here to receive more info 61
Go to Website
Contact Sales
Email this product to a friend!

PLL Synthesizer for Satcom Apps
The RoHS compliant Phase Locked Loop (PLL) PVA2125C-LF features ultra low phase noise performance of -94 dBc/Hz @ 10 kHz offset. With a frequency range of 2025 to 2226 MHz, it was designed to meet the high requirements of satellite communications and other telecom applications.
Z-Communications, Inc.
Click here to receive more info 62
Go to Website
Contact Sales
Email this product to a friend!

Expanded HDMI Test Platform
Expanded solutions for the company’s High-Definition Multimedia Interface (HDMI) test platform are designed to reduce development costs and provide accurate test results. The solutions address source testing, sink testing, media physical layer evaluation and protocol test.
Agilent Technologies
Click here to receive more info 63
Go to Website
Contact Sales
Email this product to a friend!

Low-Noise Amplifiers
A comprehensive line of low-noise amplifier modules that cover up to 18 GHz in bands, with noise figures as low as 1.8 dB, gain as high as 28 dB (+/-2 dB or less), and P1dB output power up to 20 dBm has been introduced. They are excellent choices for applications ranging from broadband test equipment to various aerospace and defense systems, and meet MIL-STD-883 requirements. The NEL-0618T620-5MH low-noise broadband amplifier, for example, covers 6 to 18 GHz, with P1dB output power of at least 20 dBm, gain of 28 dB +/-2 dB or less, and a noise figure of 4 dB. It operates from a single +12VDC supply, draws 490 mA or less, and is temperature controlled. The NEL-0102N305-1MH low-noise broadband amplifier covers 500 MHz to 2 GHz with a noise figure of 2 dB or less, gain of at least 28 dB +/-0.5 dB, and P1dB output power of at least 5 dBm. It operates from a single +12VDC supply and draws 150 mA or less.
Narda Microwave-East
Click here to receive more info 64
Go to Website
Contact Sales
Email this product to a friend!

New SMT MMIC LNA
A new low noise amplifier (LNA) is ideal for use in point-to-point radios, VSAT, military EW, ECM, and space applications from 3.5 to 7 GHz. The HMC392LC4 is a GaAs MMIC LNA which delivers 16 dB gain, 2.5 dB noise figure, and +30 dBm output IP3. It is housed in a 4 x 4mm leadless ceramic SMT package, operates from a +5V supply voltage, and features RF I/Os that are DC blocked and matched to 50 ohms with no external components. Ideal for use as a low noise front end or as a LO driver amplifier for the company’s mixer products, the HMC392LC4 functions well in surface mount, high reliability industrial, military, and space applications.
Hittite Microwave Corporation
Click here to receive more info 65
Go to Website
Contact Sales
Email this product to a friend!

Frequency Synthesizers for Ku-Band
The HLX Series of phase locked oscillators and frequency synthesizers are hermetically sealed, hybridized surface-mount products for use in military and other high-reliability ground mobile, shipboard and airborne applications. The products are available as fixed-frequency or serially-programmable frequency sources with outputs ranging from 50 MHz to over 12.5 GHz. Temperature ranges between -40 to +85ºC and small package of 0.81 x 0.81 x 0.15" are other features of the products in this series.
EM Research, Inc.
Click here to receive more info 66
Go to Website
Contact Sales
Email this product to a friend!

New Family of Rugged Embedded
The rugged flexComm™ SDR-4800 family of embedded radio modules for tactical military communications (MILCOM), data link, defense and civil satellite communications (SATCOM) systems has just been launched. The SDR-4800 product family combines high performance embedded RF and System-on-Chip (SoC) technologies with proven hardware, software and services from the SDR-4000 product line. This allows the company to deliver a highly integrated radio solution that significantly reduces the technical risk, development cost and time to deployment in its customers’ radio programs. Traditional software commercial-off-the-shelf (COTS) radio architectures typically employ separate hardware modules to accomplish the signal processing functions of the radio, from RF down/up conversion to baseband and network processing. The SDR-4000 product family combines customizable embedded RF technologies with SoC field programmable gate array (FPGA) technology on a single module to reduce the overall size and power consumption of the radio system.
Spectrum Signal Processing by Vecima
Click here to receive more info 67
Go to Website
Contact Sales
Email this product to a friend!

Microwave VME Tuner
The M/A-COM TU-6401 is a new lightweight low power SIGINT microwave tuner designed for signal search and collection applications. It provides simultaneous narrowband and wideband IF outputs centered at 160 MHz (100 MHz bandwidth) and 1 GHz (500 MHz bandwidth). The tuner’s frequency range operates from 0.5 to 18 GHz and features an RF down converter, which is integrated with a direct digital synthesizer to uncouple tuning speed from phase noise, creating the fastest high performance tuner on the market today. The M/A-COM TU-6401 is housed in a two-slot 6U VME package weighing less than seven pounds. The intermediate frequency and log video outputs are suitable for direct input into an external analog-to-digital converter for special signal processing, spectral analysis and pulse parameterization.
Tyco Electronics
Click here to receive more info 68
Go to Website
Contact Sales
Email this product to a friend!

Audio Connectors
New audio connectors, 5 and 6 pin, for ground based military communication programs have been introduced. Available styles include printed circuit mount, solder cup, and barrel cup. They comply with MIL-C-55116. Features include quick connect bayonet coupling, spring loaded contacts, sealed/water proofed, solder type contact termination, and low signal application.
Vida Products
Click here to receive more info 69
Go to Website
Contact Sales
Email this product to a friend!

AM & FM Airborne Transmitter Power
Model number SSPA 0.291-60 is a high power UHF Airborne transmitter power amplifier. This model operates at 291 MHz with an AM or FM excitation. The typical output power is 100W for FM operation, and the power is typically backed off for AM operation. This RF module offers 50 dB of typical gain. The 2nd and 3rd harmonic levels are -80 dBc maximum. The internal RF components are gated on and off in less than 500 uSec maximum. Input and output VSWR is 1.5:1 maximum. This amplifier operates from a 28Vdc power supply with a typical current of 8.75A at 100W of output power. The amplifier is biased class AB so the current increases and decreases as a function of input drive. The size of this RF amplifier is approximately a width of 9.55” with length of 4.96” and height of 4.86”. Standard features include reverse polarity protection and over voltage protection with an output isolator for PA protection. The output is fully protected from an infinite VSWR at the RF output port.
Aethercomm
Click here to receive more info 70
Go to Website
Contact Sales
Email this product to a friend!

Smaller, Tougher, Smarter Amps
A family of compact, highly efficient, tough, durable RF power amplifiers for electronic warfare and general communications applications has been released. The KMW1090 Series features three powerful, versatile amplifiers that are smaller, more efficient, and require less current. They operate under high VSWR conditions, and work with modern, complex and wideband jamming modulation techniques. The series includes Model KMW1090 (20W CW/10 to 1000 MHz), Model KMW1092 (8 to 10W CW/25 to 1000 MHz), and Model KMW1095 (30W CW/10 to 1000 MHz).
AR Modular RF
Click here to receive more info 71
Go to Website
Contact Sales
Email this product to a friend!

LDMOS Amplifier
The SM2325-53LD is a 2300 to 2500 MHz LDMOS amplifier designed for multiple wireless communications and RF heating applications in medical devices. Features include mis-match protection, single power supply, and temperature compensation.
Stealth Microwave
Click here to receive more info 72
Go to Website
Contact Sales
Email this product to a friend!

EMI/RFI Filters for Inverters
A standard range of EMC filters specially designed and optimized for inverter applications, such as servos and motor drives, the R105 series filters are compact, lightweight, and offer significant attenuation of the most critical frequencies.
EPCOS
Click here to receive more info 73
Go to Website
Contact Sales
Email this product to a friend!

Power Amplifier Transistors
A new generation of high-voltage GaAs power amplifier transistors were designed to increase the efficiency of 3G cellular base stations, which can lead to greater energy savings. These HV-HBT amplifiers can reduce waste heat by nearly 50 percent.
TriQuint Semiconductor
Click here to receive more info 74
Go to Website
Contact Sales
Email this product to a friend!


 

Ethernet OAM Test Solution
The industry’s first single-platform solution for protocol emulation and conformance testing of Ethernet Operations, Administration and Maintenance (E-OAM), has been introduced. Network equipment manufacturers and service providers can use the N2X multiservices test solution to ensure their Carrier Ethernet devices meet E-OAM performance and scalability requirements, and more.
Agilent Technologies
Click here to receive more info 75
Go to Website
Contact Sales
Email this product to a friend!

 

1 | 2 | 3 | 4 | 5 | 6 | 7


 


Copyright © 2009 Octagon Communication Inc. DBA MPDigest / MPDigest.com, All Rights Reserved.